- TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE INSTALL
- TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE SERIAL
- TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE PATCH
Most of the Cougars were made before TC introduced the wrist strengthening kit consisting of the long front tang bolt which goes all the way down through the stock, through the trigger plate, and threads into the trigger guard. Other than the stocks being very pretty and of interest due to their eye appeal, they don't have any "collectors value" as such.if it was clean I'd agree $275 was a good buy.I have some, one of which I converted to a Flintlock.īe aware there are no spare parts available unique to the Cougar like the stainless furniture.the barrel & tang are standard, the trigger asm is standard, all the internal parts of the caplock asm are stadard but the stainless hammer & sideplate would be tough to impossible to replace.the good news is that nothing much ever happens to them.and just as FYI, a standard case colored Hawken caplock asm is the exact same thing if you ever got into a situation where the lock had to be replaced completely.
TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE SERIAL
Non-glare pewter looking stainless lock and furniture, standard 15/16" x 28" x 1:48" Hawken barrel with the additional word 'Cougar' stamped on it, and 4 digit serial numbers. Highly figured presentation grade American black walnut with a stainless medallion of a Cougar perched on a rock set into the right side of the butt stock. What's it worth? Is $275 too much? Any info is helpful.Ĭlick to expand.Special runs of 5000 each in '87 and '92.45 &. What year was it made? Barrel number is 8848. Never fired best I can tell and looks brand new. Well, it came home with me.Īnyone know the TC Hawken Cougar 50? This one has a medalion on the stock, stainless furniture, double set trigs, percussion, 28" barrel, maple stock?, unknown rate of twist, and stainless tipped ramrod. I made my offer and told him to think on it.
TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE PATCH
The other had a GM barrel and the patch showed small rust. There was two ML there so I ran patches down both. It was then this old cat needed a litter box! Trying to hold in my emotions I asked if I could run a patch down the barrel. Then this old cat looked on the barrel and saw Thompson Center 50. Looked at the butt plate and nice tight fit. I'm thinking where in the heck is the blue or the brass? I flip the gun upside down and the fitting looked great. And sounded like TC ran the cougar late 80s to early 90s.Īnyhow, Went to a gun show today and ran into this ML with stainless furniture. To drill the hole, and a 8-32 thread tap.I searched past threads for the cougar and found some info about TC making special runs on rifles. Mark the front screw location with a prick punch - use a #29 drill With the rear tang screw (and aligned side to side on the tang), The back hole uses theĮxisting rear tang screw found in the rifle. Once the front screw has been secured, then mark the rearįor other traditional T/C side locks, it will only be necessary Use a #29 drillĪnd an 8-32 tap to thread the hole after it has been drilled. Use a prick punch to mark the front hole only. Then center the sight side to side on the tang. Place the sight midway between the front and rear tang screws, Two additional holes must be drilled and tapped. One or two additional holes in the tang for mounting.įor the White Mountain Carbine and Pennsylvania Hunter models, Hunting style Tang Peep Sights require the drilling of either Traditional Cap Lock or Flint Lock Muzzleloaders: Installation of the T/C Tang Peep Sight on Thompson/Center's Read the instructions included in this package before attempting
TC HAWKEN STOCK CRACK FROM THE WEDGE PIN SCREW HOLE INSTALL
WARNING - Never attempt to install a sight on a loaded firearm.Īlways ensure that the firearm is UNPRIMED AND UNCHARGED.įailure to heed this warning could result in an accidental dischargeĬausing injury and/or death to the shooter or bystanders and
7194 Hunting Style Tang Mount Peep Sightįor T/C Hawken, Renegade, Big Boar, White Mtn. Here are the instructions directly off of the T/C Hunter tang peep sight: I haven't checked in here lately, but I saw this thread and thought this might help. Then I disassembled the clamp and screw and used the perfectly certered dimple to complete the drilling and tapping process for a 10-32 screw. That assured the drill remained centered on the tang and in the proper location. Then I used a drill bit that exactly fit the hole in the sight to make a deep dimple in the tang. one part of the C was against the left side of the tang & sight and the other part of the C was against the right side of the tang & sight, thereby aligning the sight and tang perfectly).
Then I put a small C-clamp mounted sideways near the front of the assembly so the sight could not move side-to-side (i.e. To get it exactly centered, I removed the tang from the gun and used the rear tang screw to screw the tang and sight to a block of wood. The other did not, so I had to drill and tap it. One tang had a factory hole between the two tang screws. I have a TC Vernier sight on one Hawken and a TC Hunter Peep on another.
0 kommentar(er)
